Old and rusty kitchen cabinets can be upgraded without the need of tearing them entirely out. Installing new doors and painting enables you to achieve the best look without having to use a lot of cash. Kitchen cabinet refinishing Coquitlam BC can be realized by an expert, or you can consider doing the project. Below is a guideline you ought to consider if you have time.
There are some devices you require to not only make the project easy for you but also fun. You, therefore. Should buy the right tools that will allow you to carry out a good quality job. The tools you need are a vacuum, paintbrush, drill bit, tape measure, clamps, wood chisel, screwdriver, four-in-one screwdriver, hand saw, miter saw and a dust mask.
Before you start the job, you need to empty all cabinets, remove free standing appliances and clear the countertop. This provides you with space you require to do the job. You also should relocate the fittings and furniture to another room. Use paper to cover the ground and countertops and fixed appliances. This prevents the rest of the house from fumes and dust.
The next step will be to remove the drawers, shelves, and doors. The hinges should be unscrewed so that you easily remove the doors. Work strategically from right to left or top to bottom and label each one to avoid confusion when installing them back. Set aside all of the hardware you have removed and remove the old hinges and save what you will reuse.
You then should clean the entire surface. However, before cleaning, all the windows ought to be opened for the place to be ventilated. Remember to put on the dust mask. Scrub the drawer fronts, face frames, shelving, and doors with an abrasive pad dipped into a deglosser. Before the evaporation of the liquid, wipe the residue by use of a clean cloth dipped into the liquid.
Sand the entire surface with grain. Vacuuming of the outside and inside should be done so that any dust which can stain the finish is removed. Make use of a piece of clean cloth to wipe off the surface later on to remove any dirt left. The hand sanding technique is easier when the cabinets are made of oak. For maple and cherry, oil-based primers need to be utilized.
Painting should then be done. Start by working from top to bottom as you apply paint all across the grain. For the interior, use a surface mini-roller for painting that will leave a smooth texture. After painting the last coat, replace the shelf hangers when it has completely dried. You then should also prep, prime and sand both drawers and doors. The procedure you should use is the same as the one you used while working on cabinets.
This type of work is involving and messy just as realizing a complete remodeling. It is therefore important that you give it the time it deserves. Go through your timetable to determine the days and hours you will be working on it to make sure that the project is completed. You should make sure that you take the correct measurements for the best installation.
There are some devices you require to not only make the project easy for you but also fun. You, therefore. Should buy the right tools that will allow you to carry out a good quality job. The tools you need are a vacuum, paintbrush, drill bit, tape measure, clamps, wood chisel, screwdriver, four-in-one screwdriver, hand saw, miter saw and a dust mask.
Before you start the job, you need to empty all cabinets, remove free standing appliances and clear the countertop. This provides you with space you require to do the job. You also should relocate the fittings and furniture to another room. Use paper to cover the ground and countertops and fixed appliances. This prevents the rest of the house from fumes and dust.
The next step will be to remove the drawers, shelves, and doors. The hinges should be unscrewed so that you easily remove the doors. Work strategically from right to left or top to bottom and label each one to avoid confusion when installing them back. Set aside all of the hardware you have removed and remove the old hinges and save what you will reuse.
You then should clean the entire surface. However, before cleaning, all the windows ought to be opened for the place to be ventilated. Remember to put on the dust mask. Scrub the drawer fronts, face frames, shelving, and doors with an abrasive pad dipped into a deglosser. Before the evaporation of the liquid, wipe the residue by use of a clean cloth dipped into the liquid.
Sand the entire surface with grain. Vacuuming of the outside and inside should be done so that any dust which can stain the finish is removed. Make use of a piece of clean cloth to wipe off the surface later on to remove any dirt left. The hand sanding technique is easier when the cabinets are made of oak. For maple and cherry, oil-based primers need to be utilized.
Painting should then be done. Start by working from top to bottom as you apply paint all across the grain. For the interior, use a surface mini-roller for painting that will leave a smooth texture. After painting the last coat, replace the shelf hangers when it has completely dried. You then should also prep, prime and sand both drawers and doors. The procedure you should use is the same as the one you used while working on cabinets.
This type of work is involving and messy just as realizing a complete remodeling. It is therefore important that you give it the time it deserves. Go through your timetable to determine the days and hours you will be working on it to make sure that the project is completed. You should make sure that you take the correct measurements for the best installation.
About the Author:
You can find a summary of the advantages you get when you use professional kitchen cabinet refinishing Coquitlam BC services at http://www.keystonepainters.com right now.
Няма коментари:
Публикуване на коментар